Experience

EXPRO OVERSEA INC

• Norway
• Human Resources Services
• 1 - 100 Employee

• Senior Process Engineer

  • Apr 2014 - Present



Uhde Thailand

• Process Engineer

  • Sep 2011 - Present



Uhde Shedden

• Oil and Gas
• 1 - 100 Employee

• Process Engineer

  • Sep 2011 - Present

  Projects Involved  S3 Esterification, Emery Akeyung, Malaysia; Sep 2013 – present  Iowa Fertilizer Company (IFCo), USA; Aug 2012 – Aug 2013 (Oversea Assignment in UHDE GERMANY)  VRU of Jurong Rock Covern Phase 1, Singapore; May 2012 – Aug 2012  Daura RFCCU Complex, Midland Refinery, Iraq ; Sep 2011 – Apr 2012 Process Responsibilities  Perform safety relief valves calculation and its datasheets  Prepare relief load summary  Conduct drum sizing i.e. Surge Drum, Flare KO drum, two phases separator, and three phase separators as well as preparing its datasheets  Prepare, supervise and review Hazardous Area Classification done by Graduate Process Engineer  Develop drawings, i.e. PFD, DPTD, and P&IDs  Prepare HMBs for non-licensor part  Prepare, supervise and review line sizing calculation including liquid, gas/vapor, two phases, gravity, and overflow lines  Supervise and check two-phase flow of whole condensate system using ASPEN HYSYS simulation to determine line sizes, flow pattern, and steam trap ∆P  Determine utilities requirement during normal and peak flow operation of IA, PA, Raw water, and Steam  Prepare utility consumption list  Prepare, supervise, and review pump and control valve calculation as well as its datasheets  Prepare, supervise, and review instrument datasheets i.e. pressure instrument datasheets, temperature instrument datasheets, level instrument datasheet, flow meter datasheets, on/off valves, and control valves  Conduct desuperheater calculation and well as its datasheet  Prepare, supervise, and review line list  Prepare medium list Show less



thyssenkrupp Uhde

• Chemical Manufacturing
• 400 - 500 Employee

• Process Engineer (1 Year Oversea Assignment in Uhde Germany)

  • Aug 2012 - Aug 2013

   Iowa Fertilizer Company (IFCo) I have worked on Urea Synthesis and Urea Granulation Units. My responsibilities are mainly on PFDs, PFDs, H&MBs, Instrumentation Specifications preparations.  Iowa Fertilizer Company (IFCo) I have worked on Urea Synthesis and Urea Granulation Units. My responsibilities are mainly on PFDs, PFDs, H&MBs, Instrumentation Specifications preparations.



Amec Foster Wheeler

• United Kingdom
• Oil and Gas
• 700 & Above Employee

• • Jul 2007 - Aug 2011

  I have involved working on approximately 13 projects including Chemical, Oil Refineries, and Petrochemical Plants. This covers Conceptual, FEED, and EPC, for both growth filed and green field projects.Not only I have experiences in Process Design, but also a bit in Safety (4 months), Proposal Preparation (1 month), and cost estimation (1 month).Process Engineer Responsibilities Calculate hydraulic including pump circuit and gravity flow Line sizing, i.e. single phase, two phase (vap-liq, and solid-liq), and overflow RO sizing Calculate relief load and relief valve size including inlet and outlet lines Flare system design using Flarenet Simulation on revamp project Calculate breathing in and breathing out for pressure vacuum valve installed on ATM tanks Calculate accumulator drums Prepare, supervise, and review hazardous area classification Prepare and review Line list, Equipment list, Tie-in report, Utilities estimate summary, and relief and blowdown summary Prepare and review drawings, i.e. PFDs together with Heat and Material Balance, P&IDs, Design pressure and temperature diagram (DPTD), and material selection diagram (MSD) Prepare and review Equipment Process Specifications, i.e. pump datasheet, heat exchanger datasheet, drum datasheet, tank datasheet, compressor datasheet, and desuperheater datasheet Prepare and review Instrument Process Specifications, i.e control valve datasheet, temperature indicator datasheet, on/off valve datasheet, relief valve datasheet, pressure indicator datasheet, and level indicator datasheet Update process description Estimate utility consumption Conceptual design of Process configuration of 950 KBP grassroots refinery e.g. CDU, VDU, HDT, and Light Naphtha Isomerization Attend some HAZOP meetings and close out HAZOP action Show less

• • Aug 2010 - Jul 2011

   BTR project of Lanxess Butyl Rubber Pte Ltd.I was one of the process team members to work on the project. The project was executed by FWAPAC, Singapore on lump sump basis. I was responsible for Finishing Area which is to separate water from the rubber and then finish the product in form of rubber bales. I was the only one process engineer in this Area and work directly under Process Manager (Finishing Leader). Due to insufficient resource and tight schedule, I had a chance to discuss directly with Client and other disciplines, e.g. project engineer, piping engineer, mechanical engineer, instrument engineer, vessel engineer, and static engineer. Moreover, I also reviewed Vendor Datasheet, Vendor P&ID, P&ID, and datasheet from related disciplines. Show less