Experience

Worley

• Brazil
• Business Consulting and Services
• 700 & Above Employee

• IPMT - QC - TEST PACK COORDINATOR

  • Aug 2021 - Present

  Test pack Coordinator responsibilities• Review of all piping test packages. • Review work packages for completeness and latest drawing revisions• Redlining isometric drawings to add construction field welds and any field changes• Review all inspection reports and signed.• - Review and coordination of NDE and outstanding Inspection.• Monitor, records and clearing of QC related punch items.• Confirm test medium is correct according to the line list and flushing method is correct• Confirm design pressure and test pressure is correct according to line list and within the allowable pressure for the pipe specification.• Confirm filling points, venting points, and drains are acceptable.• Confirm test boundaries are reasonable - evaluate exclusion zones.• Confirm valves, instruments, etc. that need to be removed are identified.• Confirm pressure gauge and relief valve locations.• Review the test package status once the punch, punch kill activities and release for HT if punch is cleared for HT.• Maintain working relationship between owner, architect, officials, and subcontractors• Update the test package status. Show less

• Integrated Project Management Team-QC Piping & Welding

  • Jan 2020 - Jul 2021

  • Verify that all applicable welder, welding operator, and tack welder qualifications are available, current, and accurate.• Verify that a written Welding Procedure Specification (WPS) is available on site for each type of weld, the WPS is following all requirements, and the WPS has been approved as required by the construction documents• Verify that all welding consumables comply with approved documents and the approved WPS. • Verify that all electrodes are properly stored.• Verify that joint preparation, assembly practice, preheat temperatures, inter pass temperatures, welding techniques, welder performance, and post-weld heat treatment meet the requirements of approved documents, WPS, and applicable code.• Verify that the welding current and voltage are within the WPS parameters by using a calibrated hand-held volt/amp meter. Readings should be taken as near the arc as possible. • Provide early warning of potential quality problems and ensure non-conformities are being recorded based on the criticality level, through identification, tracking and close out.• Identification and Verification of materials per client/project requirement through visual inspection and document review. Perform visual/dimensional inspections during shop surveillance, welding inspections and NDE verification, witnessing hydrotest and painting/coating inspections as per the ITP. Review of all quality documents including NDT reports. Show less



GULF SPECIALIZED WORKS

• Saudi Arabia
• Oil and Gas
• 100 - 200 Employee

• PIPING & WELDING INSPECTOR

  • Mar 2019 - Aug 2019

  Responsible for Piping, Welding, NDT and equipment installation quality control activities. Controlled and monitored suppliers and Contractor's quality assurance and quality control activities. Witness Welder qualification Tests, Materials receiving Inspection. Review of pre heat and PWHT charts. Surveillance to ensure correct application of NDT on both Structural and Piping. Review of NDT reports and Radiographic films. Preparation of Hydro test Packages. Witness passivation and Chloride contamination checking. Co-ordination with clients, and preparation of QC documentation. Stage wise Inspection before, during and after fabrication for Welding. Qualifying Welders as per ASME Sec IX, AWS D 1.1 Monitoring welding consumables control and it’s storage at fabrication shop on daily basis. Reviewing of all NDT reports according to standard, project specification and procedure. Monitoring welding / visual inspection of materials like CS, Alloy steels and Stainless Steels. Material inspection - Review of Test certificates with respect to Standards. Review of heat treatment charts/PWHT procedures. Witnessing the UT, MT, PT carried out by approved NDT Agencies according code requirements. Show less



Saudi Binladen Group - PCMC

• Construction
• 1 - 100 Employee

• Welding Inspector

  • Oct 2016 - Dec 2018

  Responsible for Piping, Welding, NDT and equipment installation quality control activities. • Controlled and monitored suppliers and Contractor's quality assurance and quality control activities. • Day to day interface with EPC Contractors Inspection, Supervisory and Engineering personnel. • Witness Welder qualification Tests, Materials receiving Inspection. • Surveillance Inspection of EPC contractor’s day to day activities. • Review of pre heat and PWHT charts. • Surveillance to ensure correct application of NDT on both Structural and Piping. • Review of NDT reports and Radiographic films. • Witness passivation and Chloride contamination checking. • Co-ordination with clients, and preparation of QC documentation. Show less

• Piping & Welding Inspector

  • Oct 2015 - Sep 2016

  Responsible for Piping, Welding, NDT and equipment installation quality control activities. • Controlled and monitored suppliers and Contractor's quality assurance and quality control activities. • Day to day interface with EPC Contractors Inspection, Supervisory and Engineering personnel. • Witness Welder qualification Tests, Materials receiving Inspection. • Surveillance Inspection of EPC contractor’s day to day activities. • Review of pre heat and PWHT charts. • Surveillance to ensure correct application of NDT on both Structural and Piping. • Review of NDT reports and Radiographic films. • Preparation of Hydro test Packages. • Witness passivation and Chloride contamination checking. • Punch listing, Reinstatement activities, Witnessing Hydro tests, flushing, drying, chemical cleaning activities. • Surface profile monitoring, WFT, DFT measurements.• Monitoring Weather conditions prior to Painting.• Inspection of Heat Shrink Sleeve of field joint coating (PE) complies with the specification requirement such that DFT and Free from holiday, & other coating defects.• To participate and witness test panel painting, adhesion tests (pull off test, crosscut and Peel off test).• Witnessing Surface preparation complies with visual standard and coating complies with the project specification.• Co-ordination with clients, and preparation of QC documentation. Show less



CHEAR INDIA LIMITED

• Gudur, Andhra Pradesh, India

• QC Engineer

  • May 2014 - Jun 2015

  Responsible for Piping, Welding, NDT and equipment installation quality control activities. Controlled and monitored suppliers and Contractor's quality assurance and quality control activities. Witness Welder qualification Tests, Materials receiving Inspection. Review of pre heat and PWHT charts. Surveillance to ensure correct application of NDT on both Structural and Piping. Review of NDT reports and Radiographic films. Preparation of Hydro test Packages. Witness passivation and Chloride contamination checking. Co-ordination with clients, and preparation of QC documentation. Stage wise Inspection before, during and after fabrication for Welding. Qualifying Welders as per ASME Sec IX, AWS D 1.1 Monitoring welding consumables control and it’s storage at fabrication shop on daily basis. Reviewing of all NDT reports according to standard, project specification and procedure. Monitoring welding / visual inspection of materials like CS, Alloy steels and Stainless Steels. Material inspection - Review of Test certificates with respect to Standards. Review of heat treatment charts/PWHT procedures. Witnessing the UT, MT, PT carried out by approved NDT Agencies according code requirements. Show less



TOLEDO Electrical & Mechanical Works Company LLC

• United Arab Emirates
• Oil and Gas
• 1 - 100 Employee

• QC Piping & Welding Inspector

  • Oct 2013 - Apr 2014

  ADNOC - TAKREER - RUWAIS REFINERY EXPANSION PROJECT (RRE PHASE IV) Responsible for Piping, Welding, NDT and equipment installation quality control activities. Controlled and monitored suppliers and Contractor's quality assurance and quality control activities. Witness Welder qualification Tests, Materials receiving Inspection. Review of pre heat and PWHT charts. Surveillance to ensure correct application of NDT on both Structural and Piping. Review of NDT reports and Radiographic films. Preparation of Hydro test Packages. Witness passivation and Chloride contamination checking. Co-ordination with clients, and preparation of QC documentation. Stage wise Inspection before, during and after fabrication for Welding. Qualifying Welders as per ASME Sec IX, AWS D 1.1 Monitoring welding consumables control and it’s storage at fabrication shop on daily basis. Reviewing of all NDT reports according to standard, project specification and procedure. Monitoring welding / visual inspection of materials like CS, Alloy steels and Stainless Steels. Material inspection - Review of Test certificates with respect to Standards. Review of heat treatment charts/PWHT procedures. Witnessing the UT, MT, PT carried out by approved NDT Agencies according code requirements. Witnessing the pressure testing (Hydro / Pneumatic) activities. Witnessing the Pre commissioning inspections like Leak testing, Air blowing, Oil flushing & Water flushing. Show less



Cethar Vessels Limited

• India
• Mechanical Or Industrial Engineering
• 1 - 100 Employee

• QC Engineer

  • Dec 2012 - Sep 2013

  4x300MW Non-Coastal Thermal Power Project - SKS Power Generation Chhattisgarh LtdResponsible for Piping, Welding, NDT and equipment installation quality control activities. • Controlled and monitored suppliers and Contractor's quality assurance and quality control activities. • Day to day interface with EPC Contractors Inspection, Supervisory and Engineering personnel. • Witness Welder qualification Tests, Materials receiving Inspection. • Surveillance Inspection of EPC contractor’s day to day activities. • Review of pre heat and PWHT charts. • Surveillance to ensure correct application of NDT on both Structural and Piping. • Review of NDT reports and Radiographic films. • Witness passivation and Chloride contamination checking. • Surface profile monitoring, WFT, DFT measurements.• Monitoring Weather conditions prior to Painting.• Inspection of Heat Shrink Sleeve of field joint coating (PE) complies with the specification requirement such that DFT and Free from holiday, & other coating defects.• To participate and witness test panel painting, adhesion tests (pull off test, crosscut and Peel off test).• Witnessing Surface preparation complies with visual standard and coating complies with the project specification.• Co-ordination with clients, and preparation of QC documentation. Show less

• QC Engineer

  • Feb 2012 - Nov 2012

  Responsible for Piping, Welding, NDT and equipment installation quality control activities. • Controlled and monitored suppliers and Contractor's quality assurance and quality control activities. • Day to day interface with EPC Contractors Inspection, Supervisory and Engineering personnel. • Witness Welder qualification Tests, Materials receiving Inspection. • Surveillance Inspection of EPC contractor’s day to day activities. • Review of pre heat and PWHT charts. • Surveillance to ensure correct application of NDT on both Structural and Piping. • Review of NDT reports and Radiographic films. • Witness passivation and Chloride contamination checking. • Surface profile monitoring, WFT, DFT measurements.• Monitoring Weather conditions prior to Painting.• Inspection of Heat Shrink Sleeve of field joint coating (PE) complies with the specification requirement such that DFT and Free from holiday, & other coating defects.• To participate and witness test panel painting, adhesion tests (pull off test, crosscut and Peel off test).• Witnessing Surface preparation complies with visual standard and coating complies with the project specification.• Co-ordination with clients, and preparation of QC documentation. Show less



Bharakath Industries

• India
• Mechanical Or Industrial Engineering
• 1 - 100 Employee

• QC Engineer

  • May 2011 - Jan 2012

  MAJOR DUTIES & RESPONSIBILITIES: Stage wise Inspection before, during and after fabrication for Welding. Qualifying Welders as per ASME Sec IX, AWS D 1.1 Monitoring welding consumables control and it’s storage at fabrication shop on daily basis. Reviewing of all NDT reports according to standard, project specification and procedure. Monitoring welding / visual inspection of materials like CS, Alloy steels and Stainless Steels. Co-ordinate with NDE test as per QCP & RT Film interpretation. Monitored / Witnessed all the Welding, Fabrication related activities as per the client approved ITPs, QCPs. Witnessing the UT, MT, PT carried out by approved NDT Agencies according code requirements Preparing and review to WPS, PQR and Welder qualification for a lot of projects. Visual Inspection of Welding / Fit-up. Dimension and final inspection of the fabricated items. Review of heat treatment charts/PWHT procedures. Show less