Experience

Pirouette Medical Inc.

• United States
• Pharmaceutical Manufacturing
• 1 - 100 Employee

• Chief Operating Officer

  • Nov 2019 - Present

  Boston, Massachusetts, United States • Management of timeline and resources using project planning tools such as Gannt charts and Smartsheet. • Risk Assessment and Management – Use of Failure Modes and Effects Analysis, as well as Fault Tree Analysis • Leader of FDA Regulatory Effort – Interface with FDA, submissions confirming regulatory strategy, test plans, regulation compliance. • Document Management and Control – Developed a paper-based document control system. • Quality Control – Leading the company in… Show more • Management of timeline and resources using project planning tools such as Gannt charts and Smartsheet. • Risk Assessment and Management – Use of Failure Modes and Effects Analysis, as well as Fault Tree Analysis • Leader of FDA Regulatory Effort – Interface with FDA, submissions confirming regulatory strategy, test plans, regulation compliance. • Document Management and Control – Developed a paper-based document control system. • Quality Control – Leading the company in maintaining a quality control system. • Technical Design and Analysis – Assist the team in understanding the design limitations through technical analysis using tools such as Computational Fluid Dynamics, Finite Element Methods, and Tolerance Stack Analysis. • Human Factors Engineering – Led and performed several human factors trials to develop and iterate labeling and improve the device interface.

• Chief Engineering Officer

  • Jul 2017 - Nov 2019

  Cambridge, MA



Notre Dame Turbomachinery Laboratory

• United States
• Aviation and Aerospace Component Manufacturing
• 1 - 100 Employee

• Test Engineer

  • Sep 2016 - Jun 2017

  South Bend, Indiana Area • Worked with a team of individuals to complete performance testing of a 1.5 stage axial compressor with variable vane geometry. • Used several different measurement techniques including hot wire anemometry, total temperature, total pressure, 5 hole probe pressure measurements, unsteady wall pressure, torque, tip-timing (light probe) measurements, and dynamic strain measurements. • Data acquisition through LabView (low speed 20hz) and Apex Turbine (high-speed 200khz). • Data processed… Show more • Worked with a team of individuals to complete performance testing of a 1.5 stage axial compressor with variable vane geometry. • Used several different measurement techniques including hot wire anemometry, total temperature, total pressure, 5 hole probe pressure measurements, unsteady wall pressure, torque, tip-timing (light probe) measurements, and dynamic strain measurements. • Data acquisition through LabView (low speed 20hz) and Apex Turbine (high-speed 200khz). • Data processed steady and unsteady data using MATLAB. • Performed FEM Analysis on measurement rakes and probes with ANSYS workbench. • Designed a calibration jet for flows of up to Mach 1 and temperatures up to 1200F. • Troubleshooting of instrumentation and data anomalies. Show less



roCKet Division

• Virgin Islands, British
• Software Development
• 1 - 100 Employee

• Co-founder, Design Engineer

  • Sep 2012 - May 2013

  Applied Aerodynamics Lab - Clarkson University • Designed and large scale model rocket as the test bed for an attitude control system. • Worked to assemble a multidisciplinary engineering team to build and test the rocket. • Built test fixtures and data acquisition to assess the performance of the rocket. • Obtained funding from multiple sources, including departments within Clarkson, and local vendors. • As a joint venture with the AIAA student chapter, which I was co-chair of, we hosted a outreach day at Clarkson university… Show more • Designed and large scale model rocket as the test bed for an attitude control system. • Worked to assemble a multidisciplinary engineering team to build and test the rocket. • Built test fixtures and data acquisition to assess the performance of the rocket. • Obtained funding from multiple sources, including departments within Clarkson, and local vendors. • As a joint venture with the AIAA student chapter, which I was co-chair of, we hosted a outreach day at Clarkson university inviting local K-12 schools to come be inspired by aerospace engineering. The outreach day culminated in the launch of the rocket. Show less



Clarkson University

• United States
• Higher Education
• 700 & Above Employee

• Tutor

  • Sep 2012 - May 2013

  Potsdam, New York, United States I tutored students in higher level engineering classes, including advanced engineering mathematics, and aircraft structures.



Universität Siegen

• Germany
• Higher Education
• 1 - 100 Employee

• Research Assistant

  • Jun 2012 - Aug 2012

  Siegen, North Rhine-Westphalia, Germany Worked as a research assistant to a graduate student. I used CFX to post-process and analyze unsteady results of a locomotive cooling fan. I used MATLAB to develop animations of pressure contours on the blades. Additionally, I built a front-end GUI in MATLAB to help visualize sound pressure levels (SPL) of experimental data. This tool was used at the sponsor's facility to help those unfamiliar with MATLAB to understand the data.



Universal Instruments Corporation

• United States
• Appliances, Electrical, and Electronics Manufacturing
• 300 - 400 Employee

• Assembler

  • May 2010 - Sep 2011

  Conklin, New York, United States I worked as an assembler during the summers of 2010 and 2011. I built tightly toleranced subassemblies that were used in machines to place surface mounted circuit board components on printed circuit boards. Additionally, I was part of a lean engineering effort to increase assembly efficiency.