QA/QC Engineer

• Mar 2023 - Present

- Ensure that the works activities are going as per standers and procedures and prevent any violation of the procedure. - attained meetings with client to stand up on the interfaces and - Prepare and organize the RFI to hand over to the client. - Site inspection and supervision of the activities of mechanical work (welding, equipment installation, NDE test, HYDRO test, pump alignment). - prepare the hydro test package and follow the inspection and the test as per the procedure. - planning and preparing the Tie-in package and inspection of the golden joint (Closure joint). - official inspection with the client as per prepared RFIs. - prepare ITP and WMS of work activities and WQT for the welders. Show less

QA/QC Engineer

• Mar 2022 - Mar 2023

Rotating Equipment (Pumps, Compressors) 1. Visual inspector for Installation rotary (from foundation to final alignments. 2. Liaise with discipline Engineers, Engineering Coordinators, Engineering, Engineering Contractor, and Vendors as required in support of the progress of engineering activities 3. Supervise, Inspect and ensure that the Piping is associated with the Equipment. 4. Check the Parallelism clearance and concentricity of the Manufacturer's requirements. 5. To ensure the Preservation of all Rotating Equipment 6. Meeting with departmental needs of Construction and Contractors 7. Preservation meeting with Contractors and Clients as per schedule or as per requirements 8. Reporting directly to the Construction Manager 9. Ensure that HSE (Health, Safety, and Environment) meetings are held in all areas on a daily basis. Static Equipment (Vessels, Heat Exchangers, Columns, Tanks, Lube oil Skids): 1. Installation and alignments from foundation to final of Columns, Vessels, and Heat Exchangers. 2. Ensure the Preservation of all Static Equipment. 3. maintain Purging Pressure if it’s required (static equipment) Air coolers 1. Air Fin Fan Coolers: 2. Installation and alignments of the Air Fin Fan Coolers 3. Check the Driver and Driven assembly 4. Check the Fan Tip clearance and verification of blade angle, pitch, and belt tension of the Coolers, etc. Show less

Piping Engineer

• May 2021 - Mar 2022

1. Inspection of Fabrication and Erection for SS and CS Piping. 2. Verifying that welding inspection has been performed and joints have been released. 3. Verifying that welding inspection has been performed and joints have been released. 4. Verifying piping material identity (pipe, valves, and fittings) and its conformance to the installation drawings. 5. Preparation of daily site activity requirements. 6. Fabrication of spools. 7. Erection and installation of pipes, valves, controls valve, and connected to equipment. 8. Preparation of PTW as per HSE dep. of JV HDGSK with site requirement. 9. Planning and Load calculation of cranes and preparing lifting plan for critical erection. 10. Performing piping walk-down inspection and completing punch lists. Verifying that punch list items have been dealt with in accordance with the contractual arrangements. 11. Reviewing and verifying completeness of piping test packages (hydro or pneumatic) prior to testing. 12. Conduct the Hydro and pneumatic test as per the test package. 13. Planning and Conduct to B-punch close. 14. Flange Joint alignment and Gasket installation, Bolt Torquing. 15. Re-statement of piping. 16. Follow up MC walk down with the client to clear the punch including stress analysis. 17. Planning and Following the golden joint procedure. Show less

Power Plant Engineer

• Oct 2020 - May 2021

1. DCS operation & controlling including Testing of protection & interlocks. 2. Follow up trends and fouls by setting the set points with the operation required such as temperature and pressure. 3. Starting boilers from hot or cold start and standardizing the system from DCS and from the site. 4. Starting the turbine from hot or warm or cold start and standardizing with the grid from DCS and site. 5. Follow up cooling tower chemical addition and operation as per system required. 6. Daily report of boilers' mechanical status and consumptions of chemical addition, fuel, and water. 7. Following the schedule of Preventive maintenance and regular maintenance and making Plans for each of it. 8. Daily chemical addition like phosphate and Amin to boilers 9. Start-up activities in 60MW power plant. 10. Prepare a list of spare parts for the equipment in the new plant. 11. Read gauges, meters, and charts to track boiler operations Show less

Piping Engineer

• Sep 2018 - Aug 2020

1. Inspection of Fabrication and Erection for SS and CS Piping. 2. Verifying that welding inspection has been performed and joints have been released. 3. Verifying that welding inspection has been performed and joints have been released. 4. Verifying piping material identity (pipe, valves, and fittings) and its conformance to the installation drawings. 5. Preparation of daily site activity requirements. 6. Fabrication of spools. 7. Erection and installation of pipes, valves, controls valve, and connected to equipment. 8. Preparation of PTW as per HSE dep. of JV HDGSK with site requirement. 9. Planning and Load calculation of cranes and preparing lifting plan for critical erection. 10. Performing piping walk-down inspection and completing punch lists. Verifying that punch list items have been dealt with in accordance with the contractual arrangements. 11. Reviewing and verifying completeness of piping test packages (hydro or pneumatic) prior to testing. 12. Conduct the Hydro and pneumatic test as per the test package. 13. Planning and Conduct to B-punch close. 14. Flange Joint alignment and Gasket installation, Bolt Torquing. 15. Re-statement of piping. 16. Follow up MC walk down with the client to clear the punch including stress analysis. 17. Planning and Following the golden joint procedure. Show less

Mechanical Supervisor

• Jan 2018 - May 2018

DCC

• Apr 2017 - Sep 2017