Experience

Jet Research Center

• United States
• Oil and Gas
• 1 - 100 Employee

• Sr. Ballistics/Mechanical Technician

  • Feb 2018 - Present

  Become very familiar with the API Section 4 testing standards with regard to gas and liquid flow through various rock formations. Delt with ultra high pressure and temperature in our pressure vessels. 50,000 psi @ 400 degrees. Pressure transducer and flow meter calibration. Explosive assembly Become very familiar with the API Section 4 testing standards with regard to gas and liquid flow through various rock formations. Delt with ultra high pressure and temperature in our pressure vessels. 50,000 psi @ 400 degrees. Pressure transducer and flow meter calibration. Explosive assembly



Core Laboratories

• Netherlands
• Oil and Gas
• 700 & Above Employee

• Ballistics Technician III

  • Apr 2013 - Dec 2016

   Experienced with ballistics testing on the test range. Shot up to 32 lbs. net explosive weight in our 21 ft. 18 spf gun, always following API RP 19B recommended practices.  Familiar with API section 2 testing. I have been with Owens since the construction of our section 2 facility, and have become very familiar with the section 2 standards.  Responsible for all test preparation, setup and completion in our pressure and temperature facility. Experienced with ultra HPHT testing. (50k psi @ 500 degrees).  Responsible for supporting the engineering department with regard to test setup and conduction. If/When a test fails, offer advice or opinion on changes to product or test preparation.  Strong experience in testing plugs to API 11D1 requirements. Some of which was done with N2 under heat and pressure. Extensive experience with a wide variety of setting tools.  Proficient with Oracle and Microsoft Office Applications. Show less



EOG Resources

• United States
• Oil and Gas
• 700 & Above Employee

• Gas Lift Mechanic

  • Jan 2012 - Dec 2012

   Responsible for performing preventative maintenance on 21 units within my route. My route was the largest and included more units than any other route in EOG’s Johnson County NW and SW regions.  I am familiar with both Valerus and JW Turbocharged units and the smaller Valerus NA units. As well as, with the smaller JW 3304 units  Proficient in troubleshooting various shut down issues including no-flows and heat related issues requiring valves to be rebuilt or replaced.  Experience with the Caterpillar 3306 engine which was used to drive most of our compressors at EOG.  Familiar with the GE Gemini compressor as it was the main workhorse on the majority of our units. Show less



CCI (Culberson Construction, LLC.)

• United States
• Oil and Gas
• 1 - 100 Employee

• Flowback Hand

  • Jan 2011 - Dec 2012

   Responsible for safe rigging up and down of all well testing equipment (rigging from wellhead to sand-trap to separator to the sales line) and maintaining it through the testing phase to production.  Responsible for taking hourly readings on casing and tubing pressures, as well as gas, oil, and water produced by the well during testing, and generating a report to send in to the production company.  I have also been on a few plug milling jobs where I was responsible for maintaining flow rates for the swivel operator as well as keeping up with how much sand the well was producing while also maintaining our plug catcher.  Experience with testing, setting and adjusting test separators. Show less



Basic Energy Services

• United States
• Oil and Gas
• 700 & Above Employee

• Rigger

  • Jan 2010 - Dec 2011

   Responsible for the safe building and assembly of perforating guns used to perforate the shale formation before the fracturing process is started.  Accountable for the safe rigging up and down process of our wireline truck, crane, and other equipment used in our operations.  Certified man-lift and crane operator through Basic  Experienced in rigging pump-down stage work, as well as, plug abandonment operations, squeeze hole shooting and wet shoes.  Responsible for the safe building and assembly of perforating guns used to perforate the shale formation before the fracturing process is started.  Accountable for the safe rigging up and down process of our wireline truck, crane, and other equipment used in our operations.  Certified man-lift and crane operator through Basic  Experienced in rigging pump-down stage work, as well as, plug abandonment operations, squeeze hole shooting and wet shoes.



Excalibur Energy Services

• Glen Rose, TX

• Truck Driver

  • Jun 2008 - Dec 2010

   Accountable for safe loading and transportation of salt water from the wellsite to disposal.  Responsible for pre-trip and post-trip inspection on my transport and for all maintenance needed to keep it roadworthy.  Experience with correctly gauging and color cutting the holding tanks so our company could keep accurate readings on how much water and/or condensate each well was producing.  Assigned to a Patterson work-over rig to help with their plug drilling duties and TCP cleanouts. Show less